NUMERICAL SIMULATION RESEARCH ON CAVITATION PERFORMANCE OF THE TOOTH SIDE SHEAR CAVITATOR
-
摘要: 通过CFD Fluent对齿筒式齿侧剪切空化器进行数值模拟,分析了空化器的齿间涡、空化泡体积分数、湍动能的变化,获得转速、处理量等操作参数对空化器空化性能的影响。结果表明:空化器内的涡是生成空化泡的主要方式。定齿间和动齿间的涡是由于流体冲击壁面,与注入的流体发生回旋而产生的。而齿侧间的涡则是由于双齿侧的机械剪切形成的。充分的机械剪切和剪切面积使得齿侧间的涡分布最广,这表明增加机械剪切可有效诱导空化泡的形成。空化泡溃灭导致齿顶前缘面锐缘处的湍动能增加,并且湍动能随着转速的增加而增加,意味着该空化器既可提高空化泡含量,也可提高空化泡的溃灭率,有效提高了空化性能。但空化泡体积分数随着处理量的增加而减少,空化性能也随之降低。Abstract: In this paper, CFD Fluent was used to carry out a numerical simulation study on the tooth side shear cavitator. The changes in the cavitation between tooth vortex, the volume fraction of cavitation bubbles, and turbulent kinetic energy were analyzed. And the influence of operating parameters, such as rotation speed and processing capacity on the cavitation performance of the cavitator was obtained. The results showed that the vortex in the cavitator was the main way to generate cavitation bubbles. The vortex between the fixed teeth and the movable teeth was generated by the fluid impacting the wall surface and swirling with the injected fluid. However, the vortex between the tooth flanks was formed by the mechanical shear of the two flanks. It meant that sufficient mechanical shearing and shearing area could make the vortex distribution between tooth flanks the widest, indicating that increasing mechanical shearing could effectively induce the formation of cavitation bubbles. The collapse of cavitation bubbles caused the turbulent kinetic energy at the sharp edge of the tooth tip to increase, and the turbulent kinetic energy increased with the increase in rotational speed. It meant that the cavitator could not only increase the content of cavitation bubbles, but also increased the collapse rate of cavitation bubbles, which effectively improved the cavitation performance. However, the volume fraction of cavitation bubbles decreased with the increase of the processing volume, so as the cavitation performance.
-
[1] 张晓冬,李志义,武君,等.水力空化对化学反应的强化效应[J].化工学报,2005,56(2);262-265. [2] GOGATE P R.Cavitational reactors for process intensification of chemical processing applications:a critical review[J].Chemical Engineering & Processing Process Intensification,2008,47(4):515-527. [3] XUN S,JONG J P,HYUN S K,et al.Experimental investigation of the thermal and disinfection performances of a novel hydrodynamic cavitation reactor[J].Ultrasonics Sonochemistry,2018,49(1):13-23. [4] MARTIN P,MOJCA Z,MATEVŽ D,et al.Rotation generator of hydrodynamic cavitation for water treatment[J].Separation and Purification Technology,2013,118:415-423. [5] MANDAR B,PARAG G,ANIRUDDHA P,et al.Hydrodynamic cavitation as a novel approach for wastewater treatment in wood finishing industry[J].Separation and Purification Technology,2013,106:15-21. [6] 袁惠新,周龙远,付双成,等.齿盘剪切空化器内空化过程数值模拟研究[J].食品工业,2018,39(12):213-218. [7] 袁惠新,王赟冰,付双成,等.旋转齿筒式水力空化器内空化过程[J].食品工业,2020,41(8):203-207. [8] 郑胜寒.环隙型水力空化器的流体力学特性研究与数值模拟[D].天津:天津科技大学,2018. [9] BADVE M P,ALPAR T,PANDIT A B,et al.Modeling the shear rate and pressure drop in a hydrodynamic cavitation reactor with experimental validation based on KI decomposition studies[J].Ultrasonics Sonochemistry,2015,22(1):272-277. [10] 季斌,程怀玉,黄彪,等.空化水动力学非定常特性研究进展及展望[J].力学进展,2019,49(1):428-479. [11] 罗亮,尤宝.基于Zwart模型的化工离心泵空化性能数值模拟[J].石油化工设备,2017,46(1):24-28. [12] 韩桂华,刘亚楠,邵俊鹏,等.文丘里管内空化演变模型研究[J].系统仿真学报,2020,32(2):164-171. [13] SUN X,XUAN X X,SONG Y X,et al.Experimental and numerical studies on the cavitation in an advanced rotational hydrodynamic cavitation reactor for water treatment[J].Ultrasonics Sonochemistry,2021,70:105311. [14] MOJCA Z,TINA K,MARTIN P,et al.Shear-induced hydrodynamic cavitation as a tool for pharmaceutical micropollutants removal from urban wastewater[J].Ultrasonics Sonochemistry,2014,21(3):1213-1221. [15] 皮埃尔·弗朗,玛丽·米歇尔.空化基础[M].北京:国防工业出版社,2017. [16] BADVE M P,GOGATE P R,PANDI,et al.Hydrodynamic cavitation as a novel approach for delignification of wheat straw for paper manufacturing[J].Ultrasonics Sonochemistry,2014,21(1):162-168. [17] NI L Y,LI B,GENG G W.Numerical simulation analysis of cavitation of current limiting orifice plate[J].Earth and Environmental Science,2020,446:052064. 期刊类型引用(7)
1. 陈东,陈军辉,姜涛,梅林德. 催化燃烧工艺在制药行业VOCs废气治理中的应用. 浙江化工. 2024(02): 48-54 . 百度学术
2. 邢欣,李娜,程杰. 不同Cu负载量Cu-ZSM-5催化剂上正丁胺的选择催化氧化性能. 环境工程. 2022(03): 51-58 . 本站查看
3. 胡志斐,王振峰,汪思瀛,武文斐,侯丽敏,张凯,白心蕊. 矿物材料在催化脱硝方面的应用进展. 矿产保护与利用. 2021(01): 161-165 . 百度学术
4. 樊灏,沈振兴,逯佳琪,常甜,黄宇. 常温除甲醛催化剂Mn_1Ce_x/HZSM-5的活性位点与性能分析. 环境工程. 2021(06): 99-105 . 本站查看
5. 隗晶慧,冯勇超,于庆君,易红宏,唐晓龙,张媛媛,孟宪政,袁雨婷. 餐饮油烟中典型VOCs催化氧化研究进展. 化工进展. 2021(10): 5730-5746 . 百度学术
6. 高齐,马建,胡吉国,盛守祥,陈琛,冯俊亭. TFT-LCD制造行业VOCs排放特征及减排效果. 液晶与显示. 2020(10): 1087-1094 . 百度学术
7. 唐振艳,刘锋,左川,侯文明. 挥发性有机物催化燃烧用贵金属催化剂的研究进展. 贵金属. 2020(03): 85-93 . 百度学术
其他类型引用(4)
-

计量
- 文章访问数: 128
- HTML全文浏览量: 22
- PDF下载量: 3
- 被引次数: 11